Buy ASTM D SPECIFICATION FOR POLYETHYLENE PLASTICS EXTRUSION MATERIALS FOR WIRE AND CABLE from SAI. This standard is issued under the fixed designation D ; the 1 This specification is under the jurisdiction of ASTM Committee D20 on. ASTM D Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable.
|Published (Last):||27 April 2014|
|PDF File Size:||16.17 Mb|
|ePub File Size:||17.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
Basis of Purchase 5. Have a question about conducting the test for this standard?
ASTM D1248 Polyethylene Plastics Extrusion for Wire and Cable | Test Equipment
It is not the function of this specification to provide specific engineering data for design purposes. There is no known ISO equivalent to this standard. NOTE 17—It should be noted that the irradiation spectra from different sources including carbon arc, xenon arc, and UV?
Warning—The expected service lifetime of Class D materials is very dependent upon the speci? Prepare the specimens in accordance with Methods D for physical tests of insulations and jackets. The extrusion material for wire and cable shall be polyethylene plastic in the form of powder, granules, or pellets. March 1, 1 Revised Based on published information, ast, nominal values for the? Different tests shall be conducted in order to determine the following physical properties of extrusion materials: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
The exposure cycle consists astk a light cycle of 10 h with 18 minutes water spray on the front surface during each 2 h period followed by a dark period of 2 h with continuous water spray on the back axtm.
Make duplicate determinations from a sample of the material in the form of powder, granules, or pellets. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
ASTM D Polyethylene Plastics Extrusion for Wire and Cable | Test Equipment
J4 19  —75 Materials and Manufacture 6. Cuts test specimens from stock material Available for a wide variety of ISO and ASTM standards Consistent specimens for consistent results Manufactured with tool steel to resist damage and wear over time.
A superscript epsilon e indicates an editorial change since the last revision or reapproval. Solution viscosity is recommended as a d11248 of distinguishing such materials. Specimens shall be either die cut or machined to the speci?
Therefore, the effects of the exposures described in By means of our testing expertise and modular product design, we will help find the solution that is right for you. These parameters are for identification and not for design purposes.
Committee D20 has identi? Work Item s – proposed revisions of this standard. The former is the criterion for assignment as to type, the latter for designation as to category. Make duplicate determinations on the material in the form of powder, granules, or pellets.
Asstm standard does not purport to address all of the safety concerns, if any, associated with its use. NOTE 4—It is recognized that some high-density polyethylene plastics of very high molecular weight may have densities slightly less than 0. D — 05 Standard Speci? Link to Active This link will always route to the current Active version of the standard.
D — 05 Test specimens over 7 mm in thickness shall be conditioned for 88 h. This standard does not purport to address all of the safety concerns, if any, associated with its use. If necessary, level of contamination may be agreed upon between the seller and the purchaser.
Bench marks or a high range extensometer shall be used for the determination of elongation at break. Each of five types and categories is subdivided asrm four classes according to composition and use as follows: Deleted the existing paragraphs The molded specimen thickness shall be 1. The extrusion materials for wire and cable shall be as uniform in composition and size and as free of contamination as can be achieved by good manufacturing practice.
March 1, 1 2 3 4 5 Added a new Section Aztm, because this test is lengthy, it need not be performed on every lot of material. The values given in parentheses are mathematical conversions to inch-pound units that are provided asm information only and are not considered standard. For s1248 regarding plastic pipe materials, see Speci?
Prepare the specimens in accordance with Test Methods D for physical tests of insulation and jackets.