Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopen®, which make them easily scalable to meet requirements for both.

Author: Akidal Tygokora
Country: Cyprus
Language: English (Spanish)
Genre: Travel
Published (Last): 12 September 2004
Pages: 86
PDF File Size: 12.9 Mb
ePub File Size: 17.30 Mb
ISBN: 297-7-33873-419-6
Downloads: 79477
Price: Free* [*Free Regsitration Required]
Uploader: Mauzshura

In other words, pins connect the load to the ground.

2pcs EPEC 2024 ECU Plug 35 Car Waterproof Connector 776273 – 1 770680 – 1 and Termina

The downloading of the application programs can only be done via CAN1. Violating this rating may lead to system not recognizing all input state transitions. Otherwise operation of other inputs may be interfered Note 3: Pulse Input channels Channel 0 1 2 3 4 5 6 7 Pin X3. Any of these inputs can be logically paired with another similar input. This document contains necessary data concerning the module in question, which system designer needs in system development work.

Is dependable for the other interrupt load in module for example heavy CAN-traffic can reduce maximum frequency. If separate Epec module shock protection cover E is mounted, it is recommended to use Epec E epsc bolts?

EPEC controller Manual _Download Manual

The Color display needs extra facilities in order to have the class B covered. Monitoring epef state of the pin is generally not possible when the pin is 20024 as a PWM signal output. PWM capable outputs are divided into six groups. These kinds of pins have a small shunt resistor connected to ground. A small and protective module casing keeps inside high performance microcontroller with lots of control capabilities.

  BHARAT KO JANO QUIZ BOOK PDF

Applies to inputs used for frequency measurement and pulse counting.

Epec 3724 Control Unit

Violating this rating may lead to system not recognizing all input state transitions Note 2: Operating range 10…30 VDC? The shutdown circuit cuts off the power feed for the logic and loads in case of overvoltage.

Exceeding the max value might cause damage to input. After starting up the module measures only the pulse frequency. The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc.

In low impedance current input configuration they are subject to damage if they are connected to for example 24 volt system voltage. Please consult the manufacturer before using this pin as a module voltage supply.

Module temperature Software deadlock is monitored by the hardware watchdog that reboots the module automatically after ms software deadlock. Maximum pulse input frequency 40 kHz. There are two bit variables associated with each pin of this type in PLCopen programming environment.

There are, for example, outputs which source current and outputs which sink current. So, the practical limits are lower but the maximum values of the table still give the basis for the estimation.

  MANAGEMENT HEINZ WEIHRICH AND HAROLD KOONTZ PDF

Epec is a solution provider specialized in epe control systems, vehicle computers and information logistics systems for mobile machines. All conditions must be respected. This product complies with those certifications and standards that are listed below.

Additional module cover for wires and connectors is also available E 6. Nominal supply voltage 24 VDC? Protection for plugs depends on cable processing?

EPEC 数据手册新版_图文_百度文库

Possible to add external c-programmed library? Test method ISOpulse 5? Violating this rating may lead to system not recognizing all input state transitions Note 4: Violating this rating may lead to application program not noticing all input state transitions.

Both groups can be configured either as a current input or as a voltage input. Closed light cast aluminium housing? With input voltages below 4,3 V it seems like the internal input resistance was connected to a 1,3 V voltage source Note 2: These parameters depend on software cycle time Note 5: CAN2 is user programmable? IP67 classification according to IEC ?

Written by
admin